Most electrical calls start with something small. A light that dims when the microwave runs. A breaker that trips every few days. An outlet in the garage that has never worked right. What looks like a quick fix sometimes points to something underneath: a circuit running past its rated load, a panel that cannot keep up, or wiring that has been patched over the years without anyone looking at the whole picture. We scope that on the phone before anything is scheduled, so the visit covers what the job actually needs.
We handle electrical repair, installation, and panel work throughout Marshalltown and the surrounding Marshall County area. Homes in this city vary widely in age and wiring history, and the calls we get reflect that. Whether the issue is a single outlet or a full panel replacement, we explain what we find and price the work before it starts. We are available every day from 9 AM to 11 PM.
Call (515) 395-4989 to get a quote.
Recessed lighting installs into the ceiling itself rather than hanging from it, and the work involves cutting the ceiling, running the circuit, and connecting each can to a switch. LED retrofits are a simpler version of the same job: replacing existing fixtures with LED housings on the existing circuit. Either way, the switch wiring and the circuit load both get checked as part of the visit.
A three-way switch controls one fixture from two locations, which is standard at the top and bottom of a staircase or at either end of a long hallway. Wiring it correctly involves running a traveler wire between the two switch boxes and connecting both to the fixture. Multi-location switching adds more switches to the same circuit. These jobs are straightforward to describe and easy to get wrong, which is why a sparking or non-functioning switch in a multi-switch setup is worth a diagnostic call rather than a guess.
Fixture installation covers ceiling lights, pendant lights, sconces, and bathroom vanity bars. The visit confirms that the existing box is rated for the fixture weight, that the wiring is correct for the fixture type, and that the switch leg is properly connected. GFCI protection is required in bathrooms and other wet locations, and we verify that is in place during any lighting visit in those areas.
A breaker that trips under normal load, refuses to reset, or feels warm is telling you something about the circuit. Sometimes the breaker itself has failed and needs to be replaced. Sometimes the circuit is overloaded and needs to be split. And sometimes the panel itself is the issue: undersized for the home's current demand, or old enough that the breakers no longer function reliably. Homes in this area were wired in different decades, and it shows in the panels. A panel replacement involves load calculations, a new service panel, updated connections, and in some cases a service entrance upgrade.
Running power to a detached structure means a separate circuit from the main panel, properly sized conduit, and a subpanel or disconnect at the structure depending on the load. A shed that only needs a few outlets is a different scope than a garage with a welder, a compressor, and a ceiling heater. Electric gate operators need a dedicated circuit and weatherproof wiring at the gate location. We scope all of it on the call before the visit is scheduled.
Commercial and light industrial properties in Marshalltown carry a different kind of urgency than a residential call. A fault that takes down part of a retail floor or a production area is not a job that waits until a convenient morning. We handle out-of-hours work for commercial properties and plan the job around keeping the parts of the building that need to stay live from going down.
Commercial jobs are also planned differently from the start. Load calculations matter more when the panel is feeding equipment that runs continuously. Circuit additions in a commercial space need to account for what else is on the panel and what the service entrance can carry. We confirm that on the call and build the scope around the actual load, not a rough estimate.
If your property has a tenant in it or a business operating while the work is done, we work around that. The scope is confirmed before the visit, and the work is planned so interruptions are limited to what the job actually requires.
Small electrical problems have a way of staying small in the to-do list while they grow in the wall. An outlet that has never worked might be a tripped GFCI on a shared circuit, which is a five-minute fix. It might also be a wiring fault that has been sitting live inside the box since the outlet was first installed. A switch that sparks on contact is not always a worn switch. It can be a loose connection that is arcing every time the circuit closes, and arcing connections are one of the more common causes of electrical fires in older homes.
Outdoor fixtures are the ones that get deferred longest. A porch light that stopped working, a post light with a corroded receptacle, an exterior outlet that trips in wet weather. Outdoor wiring is exposed to more stress than indoor circuits, and a fault in an exterior box can let moisture into the circuit over time. Arc-fault and ground-fault protection on outdoor circuits exists specifically because of what happens when those conditions combine.
The jobs people put off are not always the expensive ones. Getting them diagnosed early usually costs less than dealing with what they become.
We are available every day from 9 AM to 11 PM, and that covers most of what a homeowner, landlord, or business owner needs to work around. When you call, we scope the job on the phone, confirm the price, and find a time that fits your schedule. If the problem will not wait, we take short-notice calls and will tell you on the phone what the schedule allows.
For properties with tenants, we plan the visit so the tenant knows what to expect and access is confirmed before anyone shows up. For businesses that need to stay open, we work around operating hours and limit circuit shutdowns to what the job requires. The goal is to get the work done without the building or the household having to reorganize around it.
Call in the morning. Talk it through. Know the options by the end of the call.
Not every electrical fault sits on the customer's side of the meter. When a home loses power partially or completely, the first step is working out whether the fault is in the panel, in the wiring, or upstream at the service entrance or utility connection. That distinction matters because the repair path is completely different depending on where the fault is.
We check the panel, the main breaker, and the service entrance connections during a diagnostic visit. If the fault is in the home's wiring or panel, we scope and price the repair. If it turns out the fault is on the utility's side, we explain what we found and what the next step is, which typically means contacting the utility to report the fault and request their repair. You do not pay for work we did not do, and you leave the call knowing who handles what. Everything covered is listed on our wiring and panel services page.
The price for a job is worked out on the phone before the visit is scheduled. We ask about the symptom, the location in the home, and the relevant history with the circuit or panel. From that conversation, we give you the scope and the rate before anything is booked.
A few things can change a quote once the work is underway.
If any of those shift the scope, we explain it and price it separately before proceeding. Nothing additional is done without a conversation first. Reach out and we'll get it diagnosed.
We serve Marshalltown and the communities around it throughout Marshall County, including Green Mountain, Haverhill, Albion, Ferguson, and Le Grand. If your property is in the area and you need electrical work scoped, call and we will confirm coverage when you reach us.
Not the biggest name in town. Just the one that answers. No runaround.
Check the main panel first for a tripped breaker and reset it if one is tripped. If the breaker trips again immediately, or if the affected area stays dead after the reset, that points to a fault in the circuit rather than a simple overload. Call us and describe what is happening. We will walk through what to check on the phone and get a diagnostic visit scheduled if the fault needs to be traced in person.
A panel inspection and an outlet-and-fixture check between tenants gives a landlord a documented baseline for the property's electrical condition. That record is useful if a dispute arises about pre-existing conditions, and it identifies any issues before a new tenant moves in rather than after.
The more specific you can be, the faster the call goes. Knowing which room or circuit is affected, whether the problem is constant or intermittent, and whether anything changed before the fault appeared, such as a new appliance or recent work, helps us scope the job accurately on the phone.
Yes, and grouping them is often the practical choice. If you have a list of outlets to replace, a fan to install, and a switch that needs rewiring, we can scope all of it on the call and handle everything in one visit rather than scheduling separately.
Yes. A buyer, a buyer's agent, or anyone with access to the property can schedule an inspection before closing. The inspection covers the panel, the wiring, the outlets, and the fixtures, and the findings are explained in plain terms so you know what the system holds and what it may need before the purchase is final.
Yes. Rough-in and finish work are typically two separate visits. Rough-in covers the wiring, boxes, and panel connections before the walls are closed. Finish work covers device installation, fixture hanging, and final connections after the drywall is complete. Both are scoped and scheduled as part of the same project.
When a cable is damaged by another trade, we assess the extent of the damage, identify what circuits are affected, and scope the repair. The question of who is responsible for the cost is between you and the other contractor, but the electrical repair itself is handled the same way as any other fault.
It depends on the scope. Outlet and switch replacements, panel work, and fixture installations involve little to no wall disturbance. Running new circuits through finished walls requires cutting access points, and we explain the extent of that before work begins.
Homes in this city span a wide range of construction decades, and the electrical issues reflect that. Older wiring without a ground conductor, panels that were sized for lighter loads than a modern household runs, and outlets that were added over the years without updating the circuit are all common findings. A diagnostic visit identifies what is in place and what the current condition means for the home's electrical capacity.
Outlets and lights in the same room are often on separate circuits, so a fault that kills the outlets may leave the lights unaffected. The most common cause is a tripped GFCI outlet elsewhere on the circuit, but a failed breaker or a wiring fault at the first outlet in the run can produce the same result. A diagnostic visit traces the cause.
Yes. Running power to a detached garage, a shed, or an outbuilding is a common job in this area, and the scope depends on what the structure needs to carry. A basic lighting circuit is a different project than a subpanel feeding a workshop with heavy equipment. We confirm the scope on the call and size the circuit and any subpanel to the actual load.
If you are in Marshalltown or the surrounding area and need electrical work handled, the call is the right first step. Whether the job is a tripped breaker, a panel that has been running near capacity for years, or a new circuit for an EV charger, we scope it on the phone and get it on the schedule. The communities around Marshalltown are covered too.
Call (515) 395-4989 to reach us. We are available every day from 9 AM to 11 PM.
View our complete town list. Wiring and panel work covers these nearby towns as well: Pella, Knoxville, Jefferson.
Below is a plain-language look at the electrical work we handle across Marshalltown and the surrounding Marshall County area. Each row covers what the service involves, who it fits best, and one practical detail worth knowing before you call. If your situation does not fit neatly into a row, call and describe it. We will tell you what the job involves and what it costs before anything is scheduled.
| Electrical Service | What the Job Involves | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Dedicated Appliance Circuits | Dryer and range circuitsSump pump circuit wiringKitchen circuit upgradesPanel connection for new circuits | Homeowners adding a major appliance, finishing a basement, or replacing an appliance that keeps tripping the shared circuit | A dedicated circuit runs directly from the panel to a single outlet or connection point. It prevents load conflicts and is required by code for many large appliances. |
| Backup Generator Installation | Transfer switch wiringGenerator circuit installationLoad assessmentUtility backfeed prevention | Marshalltown homeowners who have experienced multi-day outages from ice storms or severe weather | Iowa ice storms and high-wind events can knock out power for days. A properly wired transfer switch is both a code requirement and a safety requirement for any permanent hookup. |
| Electrical Panel and Service UpgradesMost Popular | 200-amp panel replacementLoad calculationsService-entrance upgradesSubpanel installation | Older homes running central air, EV chargers, or electric appliances on a 60- or 100-amp panel | Iowa's heating and cooling seasons put sustained demand on the panel. A panel that cannot carry the load becomes a bottleneck. The scope and price are confirmed before work begins. |
Call (515) 395-4989 to describe your electrical situation and get a quote. We are available daily from 9 AM to 11 PM.
(515) 395-4989