Summit Electric handles residential and commercial electrical work in Ankeny and across Polk County. Whether you need a tripped breaker diagnosed, a panel replaced, or a full rewiring of an older home, we send licensed electricians who know this area and get the job done right. With a local company, your questions go straight to the people doing the work. Licensed electricians. Code-compliant wiring. Fair rates.
Good electrical work isn't complicated, it's just done right, and it always starts with finding the actual problem.
When homeowners and business owners in Ankeny call about flickering lights, dead outlets, or breakers that keep tripping, those symptoms usually point to something specific: a loose connection, an overloaded circuit, a failing breaker, or wiring that has reached the end of its service life. Troubleshooting means following the problem wherever it leads, not just resetting the breaker and calling it done.
A typical diagnostic visit starts with a conversation about what you have noticed and when. From there, we test the circuit, check connections, and trace the issue back to its source. If the outlet that stopped working turns out to be a GFCI that tripped in another room, that gets corrected. If the flickering light points to a loose wire in the panel, we go to the panel. We also look at whether AFCI protection is in place on the circuits where arc-fault protection is now required by code, and we can install GFCI outlets anywhere the existing ones are missing or outdated.
We treat your home and its wiring the way we would our own, which means we tell you what we found and what it takes to fix it before any work starts. We'll have your outlets working again in no time.
Ankeny has a wide mix of housing, and a lot of it was built when a 100-amp service panel was considered plenty. That is no longer the case. Modern homes run dishwashers, electric dryers, EV chargers, home offices, and high-draw appliances all at once. An older panel that was sized for a different era gets overwhelmed, and the result is nuisance tripping, limited capacity for new circuits, and, in some cases, panels that are no longer safe to keep in service.
A service upgrade typically means replacing the existing panel with a new breaker box, updating the service entrance, and running load calculations to confirm the new panel can carry everything the home demands. We handle 200-amp upgrades, subpanel installation, and meter base work where it is needed as part of the same project. Dedicated appliance circuits for dryers, electric ranges, and 240-volt outlets get added at the same time when capacity is the goal.
We provide no-pressure estimates, priced up front, so you know what the project costs before anyone picks up a tool. Call today and we'll get the power back where it belongs.
Ankeny's older housing stock brings older wiring, and older wiring brings a specific set of concerns. Knob-and-tube wiring, which was standard in homes built before the mid-twentieth century, was not designed for the loads a modern household puts on it. Aluminum branch-circuit wiring, common in homes from the 1960s and 1970s, carries its own risks at connection points and device terminations. Both are jobs that licensed electricians handle regularly in this area.
Whole-home rewiring replaces the branch circuits throughout the house with modern copper wiring, updated devices, and a panel that can carry the load. Knob-and-tube replacement removes the old system and brings the home up to current code. Aluminum wiring remediation addresses the connection points where aluminum meets devices, using approved methods to reduce the risk of overheating.
Grounding and bonding are part of any rewiring project. Code-compliant wiring is also what makes a home insurable and what passes inspection when a property sells. For additions and renovations, we handle the electrical rough-in so the framing inspection goes smoothly and the finish work goes in on schedule.
We take pride in the electrical work we leave behind. One call, and an electrician is on the way.
Ankeny's residential neighborhoods span a wide range of construction eras. Newer subdivisions on the north and east sides of the city tend to have modern 200-amp panels, arc-fault protection on bedroom circuits, and wiring that meets current code. Older sections closer to the original downtown core are more likely to have 100-amp service, older breaker brands, and in some cases wiring that predates modern safety standards.
That range matters when a job comes in. A panel that looks functional from the outside may be a brand with a documented history of breaker failure. A home that has been updated in stages may have a mix of wiring types in the same walls. Knowing what is common in this area's housing stock means fewer surprises once the cover comes off the panel or the wall is opened up.
Basement circuits are a recurring item in Polk County homes. Sump pump circuits need to be on a dedicated breaker, properly grounded, and protected against the kind of moisture that basements collect. Finished basements that are being converted to living space need circuits added for outlets, lighting, and any appliances going in. We handle all of it.
Good electrical work isn't complicated, it's just done right, and that applies to every lighting job, large or small.
Recessed lighting installation, ceiling light and pendant fixtures, chandeliers, under-cabinet lighting, and ceiling fan installation and replacement are all work we handle in Ankeny homes and commercial spaces. The scope varies: some jobs are straightforward swaps at an existing box. Others involve running new wiring, adding a switch leg, or installing a fan-rated box where the original ceiling box was not designed to carry the weight.
Bathroom exhaust fans and utility exhaust fans get wired to code, with proper switching and, where required, a timer or humidity sensor. If the existing wiring is not adequate for the fixture going in, we say so before anything is installed.
We keep your home powered and safe.
Outdoor electrical work covers a broad range of jobs. Outdoor outlet installation, security lighting, motion sensor lights, and landscape lighting all require weatherproof fixtures, proper grounding, and GFCI protection at the right points. We run new circuits from the panel when the existing outdoor wiring is not adequate for what is being added.
EV charger installation is a growing part of the work we do in Ankeny. A Level 2 charger requires a dedicated 240-volt circuit sized for the charger's amperage draw. We assess the panel capacity, run the circuit, and install the outlet or hardwired connection the charger needs.
Backup generator hookup and transfer switch installation give a home a reliable path to power when the grid goes down. A generator interlock or a full transfer switch keeps the generator from back-feeding the utility line, which is a code requirement and a safety matter. Whole-home surge protection is a worthwhile addition for any home with a significant electrical load, protecting appliances and electronics from voltage spikes.
Experienced electricians who respect your home handle every part of the outdoor and specialty circuit work we take on. We'll have your outlets working again in no time.
This area has every kind of panel and circuit in it, and the commercial and rental property side of the work reflects that variety.
Property managers and landlords in Ankeny and across Polk County call us for electrical repairs between tenants, outlet and switch replacements, lighting upgrades, and panel work on multi-unit properties. Small business owners and commercial clients call for office wiring, retail electrical work, and electrical rough-in for build-outs and renovations. New construction electrical work follows the project from rough-in through trim-out and final inspection.
Electrical safety inspections are something buyers, sellers, and landlords all use. A pre-purchase inspection documents the condition of the electrical system before a sale closes. A landlord inspection confirms that a rental unit meets code before a new tenant moves in. We provide a straightforward report of what we find and what, if anything, needs attention.
For commercial clients, the process is the same as for residential: you get a price before anything is scheduled, and the scope is confirmed before work starts.
Our customers call us back because we make wiring simple, and part of that is being straightforward about what things cost.
When you call for a quote, you get a rate on the phone before anything is scheduled. For straightforward jobs like outlet replacement, ceiling fan installation, or a dedicated circuit, the price is usually confirmed in that first conversation. For larger projects like panel upgrades or whole-home rewiring, we confirm the scope and the price before work begins, so there is nothing to settle later.
What goes into an estimate depends on the job. Panel work factors in the size of the new panel, the condition of the service entrance, and whether subpanel or meter base work is needed. Rewiring projects depend on the size of the home and the extent of the existing wiring that needs to come out. EV charger installation depends on the panel capacity and the distance from the panel to the charger location. Ask what is covered and you get a straight answer.
Not the biggest name in town. Just the one that answers. No runaround.
The scope and the price are settled on the call. That is how we handle every job, from a single outlet replacement to a full-panel upgrade. You know what is being done and what it costs before an electrician is dispatched.
The same number that books the job is the number to call with questions afterward. There is no separate billing department, no callback queue, and no need to explain the job twice. You reach the same people who scheduled the work.
We serve Ankeny as our primary base of operations and take calls from across Polk County and the surrounding communities. That includes Des Moines, Altoona, Bondurant, Grimes, Johnston, and Urbandale, along with the smaller communities throughout the county.
The work varies by neighborhood. Older sections of Des Moines bring knob-and-tube and aluminum wiring. Newer developments in Grimes and Johnston tend to need EV charger circuits and panel capacity work as the homes fill up with modern appliances. Bondurant and Altoona have a mix of newer builds and older properties where panel upgrades come up regularly. Whatever the job and wherever it is in the area, we send licensed electricians who know what they are looking at.
The electrician will confirm what you called about and take a look at the area involved before doing anything else. From there, you get a clear explanation of what is found and what the fix involves before any work starts. Work is performed by licensed electricians who treat your home and its wiring the way they would their own.
Ankeny's neighborhoods span a wide range of construction eras, from post-war homes with aging panels and older wiring to newer subdivisions with modern 200-amp service. Knowing what is common in this area's housing stock means fewer surprises when the panel cover comes off or the wall is opened up. That familiarity shapes how we scope the job and what we check during a diagnostic visit.
Clear communication at every step makes the biggest difference. We go over the job on the call, confirm the price before anyone arrives, and explain what we found before touching anything. If the scope changes once the work is underway, we let you know before proceeding.
Call us at (515) 395-4989 and describe what you are seeing. We stand behind the work we do, and if something is not right, we work through it with you. The same number that booked the job is the number to call with questions afterward.
Yes. We keep the work area as clean as we found it, which includes cleaning up any debris from outlet or panel work and leaving the space in order before we go. For larger jobs that involve opening walls or running new wiring, we let you know what to expect in terms of any patching or finishing that falls outside the electrical scope.
Knob-and-tube and aluminum branch-circuit wiring both show up regularly in older Ankeny homes, and each requires a specific approach. Aluminum wiring, for example, needs approved connectors and device terminations to reduce the risk of overheating at connection points. Knowing what to look for and how to handle it correctly is what separates a proper remediation from a patch job.
Work is performed by licensed electricians who explain what they find, give you the price before starting, and treat your home with care. You get a straight answer when you ask a question, and the scope is confirmed before anything is touched. We take pride in the electrical work we leave behind.
Summit Electric is available every day from 9:00 AM to 9:00 PM to take calls for electrical repairs, panel upgrades, wiring projects, EV charger installation, generator hookups, and everything in between. We serve homeowners, property managers, and commercial clients throughout Ankeny and Polk County.
Call (515) 395-4989 to get a quote. The price is confirmed before anything is scheduled, and the electricians who show up are licensed and know this area's housing stock.
Call in the morning. Powered by afternoon. Follow-up when you need it.
(515) 395-4989